開槽和無槽六角凸緣頭（墊圈頭）螺釘 (ASTM F837,F468) [TABLE 2.2.10-1] ASME B 18.6.3 (H10A) - 2024
| 選擇規格尺寸 點擊↓ 2# 3# 4# 5# 6# 8# 10# 12# 1/4 5/16 3/8 7/16 1/2 |
尺寸單位:
inch |
|
![ASME B 18.6.3 (H10A) - 2024 開槽和無槽六角凸緣頭（墊圈頭）螺釘 (ASTM F837,F468) [TABLE 2.2.10-1]](https://img.164580.com/upload/48/pic_cadpara/1491_zh.png?ue=1761524522&local=cache&tp=canvas&pict=png)
![美標ASME B18.6.3 (H10A) - 2024 ASME18.6.3 開槽和無槽六角凸緣頭（墊圈頭）螺釘 (ASTM F837,F468) [TABLE 2.2.10-1]](https://img.164580.com/upload/48/pic/2023/11/17/1700200986685979827.jpg)
![美標ASME B18.6.3 (H10A) - 2024 ASME18.6.3 開槽和無槽六角凸緣頭（墊圈頭）螺釘 (ASTM F837,F468) [TABLE 2.2.10-1]](https://img.164580.com/upload/48/pic/2023/11/17/1700201088233464801.jpg)
![ASME B 18.6.3 (H10A) - 2024 開槽和無槽六角凸緣頭（墊圈頭）螺釘 (ASTM F837,F468) [TABLE 2.2.10-1]](https://img.164580.com/upload/48/qrcode_standardurl/24959.png)
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ①,機械螺釘的螺紋長度： 1）螺紋規格≤5#: 公稱長度≤3倍公稱直徑的應為滿扣產品，頭下螺紋肩距≤1倍螺距。 公稱長度＞3倍公稱直徑到 1-1/8 in 的，允許頭下肩距最大不超過2倍螺距。 若無其他規定，長螺釘的最小螺紋長度為1 in 。 2）螺紋規格≥6#: 公稱長度≤3倍公稱直徑的應為滿扣產品，頭下螺紋肩距≤1倍螺距。 公稱長度＞3倍公稱直徑到 2 in 的，允許頭下螺紋肩距最大不超過2倍螺距。 若無其他規定，長螺釘最小螺紋長度為 1.5 in 。 ②,除非用戶有要求，六角頭凸緣螺釘不需要開槽。 ③,六角面與凸緣頂面結合處的圓角半徑R應不大于螺釘公稱直徑的0.15倍。 ④,可選擇凹穴型式。 ⑤,螺桿直徑ds應不小于2A級螺紋最小中徑，并不大于公稱（基本）螺紋大徑。 ⑥,凹穴型凹穴底部以下的槽深應不小于規定最小槽深的1/3。 ⑦,六角頭表面允許所有的邊緣和棱角略有圓鈍。 ⑧,對邊距離和對角距離應在最大部位測量。六角面的斜度（六角面與軸心線之間的夾角）應不超過2°或0.004英寸，以較大者為準，該面應是對邊寬度數值較大的平面。 ⑨,由于金屬未完全填滿而造成的六角圓鈍應盡可能一致。當用直徑等于規定的最小對角距離的測量量規測量時，頭部凸出在量規外的高度，應等于或大于原件表格中的F值。六角頭對角測量的相關描述詳見強制性附錄II。 |
同版本產品組
長度公差
Machine screws can be made to any length, but they are generally produced in fractional length increments of 1/16 in. for screws up to 5/8 in. long, 1/8 in. for screws over 5/8 in. through 1-1/2 in. long, and 1/4 in. for screws over 1-1/2 in. long.
標稱螺釘尺寸的長度公差 | |||
標稱螺釘長度 | 螺紋規格 | ||
0000~00 | 0~12 | 1/4~3/4 | |
≤1/2 | -0.01 | -0.02 | -0.03 |
＞1/2,≤1 | -0.02 | -0.03 | -0.03 |
＞1,≤2 | / | -0.06 | -0.06 |
＞2 | / | -0.09 | -0.09 |
類似標準及供貨信息
| 1 |
![六角頭凸緣（帶墊）螺栓 1型 [Table JA.2]](http://img.164580.com/upload/48/pic/2023/11/17/1700201088392116642.jpg)
|
[日標] JIS B 1189 (Type 1) - 2014 |
六角頭凸緣（帶墊）螺栓 1型 [Table JA.2] Hexagon Bolt with flange (Collar) - Type 1 - [Table JA.2] 供應商(1) |
| 2 |
|
[日標] JIS B 1189 (Type 1) - 2005 |
六角頭帶墊螺栓 1型 Hexagon Flange with Flat Upper Face Bolt - Type 1 [Attached Table 1] 供應商(1) |
| 3 |
|
[日標] JIS B 1189 (Class 1) - 1977 |
六角頭墊圈面螺栓 1型 Hexagon Bolts with Collar - Class 1 供應商(1) |
| 4 |
|
[法國] NF E 27-711 - 1982 |
六角凸緣螺栓 8.8級、10.9級 Hexagon Bolt with Collar |
| 5 |
|
[澳標] AS /NZS 1427 - 1996 |
米制小系列六角頭帶介螺栓 ISO Metric Small Series Hexagon Washer Head Screws |
| 6 |
![十字槽六角凸緣頭螺釘 [TABLE 2.2.10-2 I]](http://img.164580.com/upload/48/pic/2023/11/17/1700206049299184076.jpg)
|
[美標] ASME B 18.6.3 (H10B-I) - 2024 |
十字槽六角凸緣頭螺釘 [TABLE 2.2.10-2 I] Cross Recess Indented Hex Washer Head Screws [TABLE 2.2.10-2] |
| 7 |
![梅花槽六角凸緣頭螺釘 [TABLE 2.2.10-2 VI]](http://img.164580.com/upload/48/pic/2023/11/17/1700206021249998460.jpg)
|
[美標] ASME B 18.6.3 (H10B-VI) - 2024 |
梅花槽六角凸緣頭螺釘 [TABLE 2.2.10-2 VI] Recess Dimensions for Indented Hex Washer Head Screws, Type VI [TABLE 2.2.10-2 VI] |
| 8 |
![開槽和無槽六角凸緣頭（墊圈頭）螺釘 [Table 32] (ASTM F837, F468)](http://img.164580.com/upload/48/pic/2023/11/17/1700200986084395472.jpg)
|
[美標] ASME B 18.6.3 (T32) - 2013 |
開槽和無槽六角凸緣頭（墊圈頭）螺釘 [Table 32] (ASTM F837, F468) Plain and Slotted Hex Washer Head Screws [Table 32] (ASTM F837, F468) |
| 9 |
|
[美標] ASME B 18.6.3 (T33-I) - 2013 |
十字槽六角凸緣頭螺釘 Cross Recess Dimensions for Indented Hex Washer Head Screws |
| 10 |
|
[美標] ASME B 18.6.3 (T33-VI) - 2013 |
梅花槽六角凸緣頭螺釘 Recess Dimensions for Indented Hex Washer Head Screws，Type VI |