會員中心 | English | 繁體中文

MJ螺紋光桿公差帶f9六角頭螺栓 GJB 3374 (/5) - 1998

選擇規格尺寸點擊↓

尺寸單位: mm

軍標GJB 3374 (/5) - 1998 GJB3374 3374GJB MJ螺紋光桿公差帶f9六角頭螺栓

掃一掃分享

單重計算公差最小破壞扭矩牌號等級

千件重及價格計算千件重 : kg x 元/kg = 元/千件

默認密度 g/cm³

公稱長度L 注:選擇后獲得 相應重量 等

公稱直徑
d

d₁
d	最大值
d	最小值
H	最大值=公稱
H	最小值
s	最大值=公稱
s	最小值
e	最小值
b	參考
r	最大值
r	最小值
d₂	最小值=公稱
d₂	最大值
C	參考
h	最大值
h	最小值
d₃	最小值

MJ4×0.7	MJ5×0.8	MJ6×1	MJ8×1	MJ10×1.25	MJ12×1.25	MJ14×1.5	MJ16×1.5	MJ18×1.5	MJ20×1.5
3.99	4.99	5.99	7.987	9.987	11.984	13.984	15.984	17.984	19.98
3.96	4.96	5.96	7.951	9.951	11.941	13.941	15.941	17.941	19.928
2.5	3	3.5	4.5	5	6	7	8	8	10
2.25	2.75	3.2	4.2	4.7	5.7	6.64	7.64	7.64	9.64
7	8	10	13	17	19	22	24	27	30
6.85	7.85	9.78	12.73	16.73	18.67	21.67	23.67	26.67	29.67
7.6	8.7	10.9	14.4	18.9	21.1	24.5	26.8	30.2	33.6
8.6	10.4	12	14.5	18	20	23	25.5	28	30.5
0.4	0.5	0.7	0.7	0.8	0.9	1.1	1.1	1.3	1.3
0.2	0.3	0.5	0.5	0.6	0.6	0.8	0.8	1	1
1	1.6	1.6	2	2.5	2.5	2.5	3.2	3.2	3.2
1.14	1.74	1.74	2.14	2.64	2.64	2.64	3.38	3.38	3.38
2.5	3	3	4	4	4.5	4.5	5	5	5.5
0.5	0.5	0.5	0.5	0.6	0.6	0.6	0.6	0.6	0.6
0.2	0.2	0.2	0.2	0.3	0.3	0.3	0.3	0.3	0.3
6.4	7.4	9.3	12.2	16	18	21	23	26	29

L₂ ±0.2

千件鋼制重≈kg

①,D1（參考）= S。
②,當L超過154mm時，其間隔取4mm。
③,材料：30CrMnSiA；熱處理：σb=1100~1280MPa；表面處理：d≤8mm 鍍鋅鈍化，d＞8mm 鍍鎘鈍化。
④,頭部可按 HB 0-9-1983制保險孔。
⑤,標志按 HB 0-3-1983。
⑥,其余要求按通用規范 GJB 3376。

同版本產品組

GJB 3374 (/1~/4) - 1998

GJB 3374 (/12) - 1998

MJ螺紋光桿公差帶f9短螺紋小六角頭螺栓

GJB 3374 (/13~/15) - 1998

MJ螺紋光桿公差帶h8短螺紋小六角頭螺栓

GJB 3374 (/16~/18) - 1998

鉸鏈連接用MJ螺紋光桿公差帶f7小六角頭螺栓

GJB 3374 (/19~/21) - 1998

鉸鏈連接用MJ螺紋光桿公差帶h6小六角頭螺栓

GJB 3374 (/22~/24) - 1998

MJ螺紋十字槽盤頭螺栓

GJB 3374 (/25~/26) - 1998

MJ螺紋十字槽扁圓頭螺栓

GJB 3374 (/27~/28) - 1998

MJ螺紋扁圓頭錐端螺栓

GJB 3374 (/29) - 1998

MJ螺紋十字槽100°沉頭螺栓

GJB 3374 (/30) - 1998

MJ螺紋光桿公差帶f9十字槽100°沉頭螺栓

GJB 3374 (/31) - 1998

MJ螺紋十字槽100°沉頭錐端螺栓

GJB 3374 (/32) - 1998

MJ螺紋光桿公差帶h8短螺紋十字槽100°沉頭螺栓

GJB 3374 (/33) - 1998

MJ螺紋光桿公差帶r6短螺紋十字槽100°沉頭螺栓

引用參考

GB /T 1172 - 1999

黑色金屬硬度及強度換算值

GB /T 5267.1 - 2002

鍍鋅、鍍鎳、鍍鎘、復合鍍等層鍍層鹽霧腐蝕的防護性能

GB /T 193 - 2003

普通螺紋（一般用途米制螺紋）- 直徑與螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

緊固件 - 螺栓、螺釘和螺柱 - 公稱長度和螺紋長度 (ISO 888:2012, MOD)

GB /T 12603 - 2005

金屬熱處理工藝分類及代號

GB /T 3 - 1997

普通螺紋收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 一般要求

GB /T 5779.3 - 2000

緊固件表面缺陷 - 螺栓、螺釘和螺柱 - 特殊要求

注：技術數據僅供參考，請以官方原件為準！

類似標準及供貨信息

1	[國標] GB /T 31.1 - 2013	六角頭螺桿帶孔螺栓 Hexagon Bolts with Split Pin Hole on Shank 供應商(3)
2	[國標] GB /T 31.1 - 1988	六角頭螺桿帶孔螺栓 A和B級 Hexagon Bolts with Split Pin Hole on Shank A and B 供應商(3)
3	[國標] GB 31.2 - 1988	細桿六角頭螺桿帶孔螺栓 B級 Hexagon Bolts with Split Pin Hole On Shank-Reduced Shank-Product Grade B 供應商(1)
4	[國標] GB 31.3 - 1988	六角頭螺桿帶孔螺栓細牙 A和B級 Hexagon Bolts with Split Pin Hole on Shank-Fine Pitch Thread-Product Grade A and B 供應商(1)
5	[國標] GB 23 - 1976	小六角頭螺桿帶孔螺栓 Bolts, Small Hexagon Head with Hole Through The Shank
6	[國標] GB 24 - 1976	小六角頭螺桿帶孔導頸螺栓 Bolts, Small Hexagon Head with Fit Neck and Hole Through The Shank
7	[德標] DIN 65526 - 2016	航空航天 - 六角頭螺栓,緊公差,MJ短螺紋,鈦合金 - 在315℃以下時額定抗拉強度為1100MPa Aerospace Series - Hexagon Bolts, Close Tolerance, with Short-length MJ Thread, Titanium Alloy, Nominal Tensile Strength 1100 Mpa, for Temperatures up to 315℃
8	[汽標代號] Q 173	六角頭螺桿帶孔螺栓 Hexagon Head with Hole Through The Shank
9	[汽標代號] Q 173B	細牙六角頭螺桿帶孔螺栓 [細牙普通螺紋] Hexagon Bolts with Split Pin Hole on Shank-Fine Pitch Thread
10	[汽標代號] Q 173C	細牙六角頭螺桿帶孔螺栓 [較細牙普通螺紋] Hexagon Bolts with Split Pin Hole on Shank-Fine Pitch Thread
11	[英標] BS 1768 - 1963	精制美制六角頭桿部帶孔螺栓 Unified Hexagon Head Bolts, Washer Faced
12	[俄標] GOST 7796 (-2) - 1970	桿部帶孔六角頭螺栓 2型 Hexagon Reduced Head Bolts Product Grade B, Type 2
13	[俄標] GOST 7796 (-5) - 1970	六角頭螺栓 5型 Hexagon Reduced Head Bolts Product Grade B, Type 5
14	[俄標] GOST 7798 (2) - 1970	六角頭桿頭帶孔螺栓 Hexagon Bolts with Split Pin Hole on Shank
15	[俄標] GOST 7805 (-2) - 1970	六角頭螺栓桿部帶孔 2型 Hexagon Bolts, Split Pin Hole, Product Grade A, Type 2
16	[電力] DL /T 764 - 2014	電力金具用螺桿帶銷孔六角頭螺栓 Hexagon Head Bolts with Split Pin Hole on Shank for Electric Power Fittings
17	[電力] DL /T 764.1 - 2001	電力金具專用緊固件 - 六角頭帶銷孔螺栓 Electric Power Fitting Fasteners Hexagon Head Bolts with Split Pin Hole on Shank
18	[軍標] GJB 3371 (/1~/9) - 1998	普通螺紋螺栓 Hexagon Bolts with M Thread
19	[軍標] GJB 3371 (/10 ~ /18) - 1998	短螺紋小六角頭螺栓 Small Hexagon Bolts with Short M Thread
20	[軍標] GJB 3371 (/19) - 1998	光桿公差帶f9六角頭螺栓 Hexagon Head Bolts，Shank Tolerance f9
21	[軍標] GJB 3371 (/77~/78) - 1998	光桿公差帶r6短螺紋六角頭螺栓 Hexagon Head Bolts, Short Thread, Shank Tolerance r6
22	[軍標] GJB 3371 (/20) - 1998	光桿公差帶f9短螺紋小六角頭螺栓 Small Hexagon Head Bolts, Short Thread, Shank Tolerance r6
23	[軍標] GJB 3371 (/21~/24) - 1998	光桿公差帶h8短螺紋小六角頭螺栓 Small Hexagon Head Bolts, Short Thread, Shank Tolerance h8
24	[軍標] GJB 3371 (/25~/28) - 1998	鉸鏈連接用光桿公差帶f7小六角頭螺栓 Small Hexagon Head Bolts, Shank Tolerance f7
25	[軍標] GJB 3371 (/29~/32) - 1998	鉸鏈連接用光桿公差帶h6小六角頭螺栓 Small Hexagon Head Bolts, Shank Tolerance h6
26	[軍標] GJB 3371 (/69) - 1998	光桿公差帶f9短螺紋六角頭螺栓 Hexagon Head Bolts, Short Thread, Shank Tolerance f9
27	[軍標] GJB 3372 (/1~/10) - 1998	六角頭螺釘桿部帶孔 Hexagon Bolts, Split Pin Hole
28	[軍標] GJB 3374 (/1~/4) - 1998	MJ螺紋六角頭螺栓 MJ Thread, Hexagon Head Bolts
29	[軍標] GJB 3374 (/6) - 1998	MJ螺紋光桿公差帶f9短螺紋六角頭螺栓 Hexagon Head Bolts, Short Thread, Shank Tolerance f9, MJ Thread
30	[軍標] GJB 3374 (/7) - 1998	MJ螺紋光桿公差帶r6短螺紋六角頭螺栓 Hexagon Head Bolts, Short Thread, Shank Tolerance r6, MJ Thread
31	[軍標] GJB 3374 (/12) - 1998	MJ螺紋光桿公差帶f9短螺紋小六角頭螺栓 Small Hexagon Head Bolts, Short Thread, Shank Tolerance f9, MJ Thread
32	[軍標] GJB 3374 (/13~/15) - 1998	MJ螺紋光桿公差帶h8短螺紋小六角頭螺栓 Small Hexagon Head Bolts, Short Thread, Shank Tolerance h8, MJ Thread
33	[軍標] GJB 3374 (/16~/18) - 1998	鉸鏈連接用MJ螺紋光桿公差帶f7小六角頭螺栓 Small Hexagon Head Bolts with Clevis End, Short Thread, Shank Tolerance f7, MJ Thread
34	[軍標] GJB 3374 (/19~/21) - 1998	鉸鏈連接用MJ螺紋光桿公差帶h6小六角頭螺栓 Small Hexagon Head Bolts with Clevis End, Short Thread, Shank Tolerance h6, MJ Thread
35	[航天] QJ 2367 - 1992	六角頭螺桿帶孔螺栓
36	[航空] HB 1- 101 - 2002	六角頭螺栓 Hexagon Bolts 供應商(1)
37	[航空] HB 1- 201 - 1995	六角頭螺釘 Hexagon Head Screws 供應商(1)