會員中心 | English | 繁體中文

十字槽82度沉頭AB ABR自攻螺釘 ASME B 18.6.3 (T2-I/T2-IA+T40) - 2013

選擇規格尺寸點擊↓

10#

12#

1/4

5/16

3/8

7/16

1/2

ASME B 18.6.3 (T2-I/T2-IA+T40) - 2013 十字槽82度沉頭AB ABR自攻螺釘

尺寸單位: inch

美標ASME B18.6.3 (T2-I/T2-IA+T40) - 2013 A 十字槽82度沉頭AB ABR自攻螺釘

掃一掃分享

公差

螺紋尺寸
d

d ^①	公稱
PP
d_k	最大值
	最小值
k	參考值
M₁	I 型
M₂	IA型
P	I 型最大值
	I 型最小值
	IA型最大值
	IA 型最小值
槽號	I 型
	IA型
α	最小值
	最大值
L₀ ^④	公稱
Y ^④	最大值	螺紋過渡長度(全螺紋)
b ^④	最小值	螺紋長度 (長螺釘)

0.0600	0.0730	0.0860	0.0990	0.1120	0.1250	0.1380	0.1510
48	42	32	28	24	20	20	19
0.112	0.137	0.162	0.187	0.212	0.237	0.262	0.287
0.096	0.120	0.144	0.167	0.191	0.215	0.238	0.262
0.035	0.043	0.051	0.059	0.067	0.075	0.083	0.091
0.062	0.070	0.096	0.100	0.122	0.148	0.168	0.176
0.062	0.070	0.096	0.100	0.122	0.148	0.168	0.176
0.036	0.044	0.056	0.061	0.082	0.075	0.095	0.103
0.020	0.028	0.040	0.045	0.066	0.052	0.072	0.080
0.037	0.045	0.053	0.058	0.079	0.071	0.091	0.099
0.021	0.029	0.037	0.042	0.063	0.053	0.073	0.081
0	0	1	1	1	2	2	2
0	0	1	1	1	2	2	2
80°	80°	80°	80°	80°	80°	80°	80°
82°	82°	82°	82°	82°	82°	82°	82°
7/16	9/16	5/8	3/4	13/16	15/16	1	1-1/8
0.021	0.024	0.031	0.036	0.042	0.050	0.050	0.053
0.360	0.440	0.520	0.590	0.670	0.750	0.830	0.910

螺紋尺寸
d

10#

12#

1/4

5/16

3/8

7/16

1/2

d ^①	公稱
PP
d_k	最大值
	最小值
k	參考值
M₁	I 型
M₂	IA型
P	I 型最大值
	I 型最小值
	IA型最大值
	IA 型最小值
槽號	I 型
	IA型
α	最小值
	最大值
L₀ ^④	公稱
Y ^④	最大值	螺紋過渡長度(全螺紋)
b ^④	最小值	螺紋長度 (長螺釘)

0.1640	0.1900	0.2160	0.2500	0.3125	0.3750	0.4375	0.5000
18	16	14	14	12	12	10	10
0.312	0.362	0.412	0.477	0.597	0.717	0.760	0.815
0.285	0.333	0.380	0.442	0.556	0.670	0.715	0.765
0.100	0.116	0.132	0.153	0.191	0.230	0.223	0.223
0.182	0.198	0.262	0.276	0.358	0.386	0.402	0.418
0.182	0.198	0.262	0.276	0.358	0.386	0.402	0.418
0.110	0.125	0.139	0.154	0.196	0.225	0.241	0.256
0.087	0.102	0.116	0.131	0.174	0.203	0.219	0.234
0.107	0.122	0.136	0.151	0.193	0.222	0.238	0.253
0.089	0.104	0.118	0.133	0.175	0.204	0.22	0.235
2	2	3	3	4	4	4	4
2	2	3	3	4	4	4	4
80°	80°	80°	80°	80°	80°	80°	80°
82°	82°	82°	82°	82°	82°	82°	82°
1-1/4	1-3/8	1-5/8	1-13/16	1-13/16	1-7/8	1-7/8	1-7/8
0.056	0.062	0.071	0.071	0.083	0.083	0.100	0.100
0.980	1.140	1.300	1.500	1.500	1.500	1.500	1.500

①,若以小數規定公稱直徑，應省略小數前和小數點后第四位的零。
②,螺釘末端釘尖上不允許因螺紋輾壓而形成的虛尖，允許略帶圓弧或圓鈍形末端。
③,小于等于8#的螺釘，螺紋牙頂平面寬度不應超過0.004in，大于8#的應不超過0.006in。
④,正常情況下，當螺釘長度小于等于其公稱長度L0時應采用全螺紋，過渡螺紋長度應小于等于Y；若螺釘長度大于其公稱長度L0可采用半牙型式，但其螺紋長度應不小于b。

7	[國標] GB /T 846 - 2017	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws 供應商(5)
8	[國標] GB /T 846 - 1985	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws 供應商(5)
9	[國標] GB 846 - 1976	十字槽沉頭自攻螺釘 Cross Recessed Countersunk Head Self-tapping Screws 供應商(5)
10	[德標] DIN 7982 - 1990	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws 供應商(3)
11	[國際] ISO 7050 - 2011	十字槽沉頭自攻螺釘 Cross Recessed Countersunk (Flat) Head Tapping Screws 供應商(1)
12	[國際] ISO 7050 - 1983	十字槽沉頭自攻螺釘 Cross Recessed Countersunk Head Tapping Screws 供應商(1)
13	[日標] JIS B 1122 (T6) - 2015	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws
14	[日標] JIS B 1122 (JA4) - 2015	十字槽沉頭自攻釘 - 螺紋型式：Class 1~Class 4 Cross Recessed Countersunk Head Tapping Screws - Threaded Portion are of Class 1 to 4
15	[日標] JIS B 1125 - 2015	十字槽喇叭頭自攻釘 Cross Recessed Trumpet Head Self Drilling Tapping Screw
16	[日標] JIS B 1125 - 2015	十字槽沉頭帶筋自攻釘 Flex. Purpose Drilling Tapping Screws
17	[日標] JIS B 1125 - 2003	十字槽喇叭頭自攻釘 cross Recessed Trumpet Head Self Drilling Tapping Screw
18	[日標] JIS B 1125 - 2003	十字槽沉頭帶筋自攻釘 Cross Recessed Ribbed Countersunk Head Tapping Screws
19	[日標] JIS B 1122 (AAT2) - 1996	十字槽沉頭自攻釘 - 螺紋型式：Class 1~Class 4 [附表2] Cross Recessed Countersunk Head Tapping Screws - Threaded Portion are of Class 1 to 4 [Annex Attached Table 2]
20	[日標] JIS B 1122 (AT2) - 1996	十字槽沉頭自攻釘 [表2] Cross Recessed Countersunk Head Tapping Screws [Table 2]
21	[日標] JIS B 1125 - 1995	十字槽喇叭頭自攻釘 Cross Recessed Bugle Head Self-drilling Tapping Screws
22	[汽標代號] Q 274	十字槽沉頭自攻螺釘 C型 Cross Recessed Countersunk Head Tapping Screws - Type C
23	[汽標代號] Q 278	十字槽沉頭自攻螺釘 F型 Cross Recessed Countersunk Head Tapping Screws - Type F
24	[美標] ASME/ANSI B 18.6.3 - 2010	80°十字槽沉頭自攻釘 80° Machine Screw and Tapping Screw Nuts (Inch Seires)
25	[意大利] UNI 9709 - 1990	塑料用雙螺紋十字槽沉頭(平頭)自攻螺釘 Two-thread Countersunk (Flat) Head Tapping Screws with Cross Rocessed for Plastics
26	[意大利] UNI 6955	十字槽沉頭自攻釘 Cross-Recessed Flat Countersunk Head Tapping Screws
27	[法國] NF E 25-656 - 1994	十字槽沉頭自攻螺釘 Cross Recessed Countersunk (Flat) Head Tapping Screws
28	[英標] BS 4174 - 1972	米字槽80°沉頭自攻釘 [Table 9] Recess 80°countersunk Head Screws - Type Z [Table 9]
29	[英標] BS 4174 - 1972	米字槽80°沉頭清根自攻釘 [Table 11] Recess 80°Truncated Countersunk Head Screws - Type Z [Table 11]
30	[澳標] AS /NZS 4407 - 1996	米制十字槽沉頭自攻螺釘 ISO Metric Cross Recessed Countersunk Head Tapping Screws
31	[原電子工業部] SJ 2822 - 1987	十字槽沉頭自攻釘
32	[原電子工業部] SJ 2498 - 1984	十字槽沉頭自攻釘
33	[韓標] KS B 1032 - 2016 (R2021)	十字槽沉頭自攻螺釘 Cross-Recessed Countersunk (Flat) Head Tapping Screws
34	[韓標] KS B 1032 - 2001	十字槽沉頭自攻螺釘 Cross-Recessed Countersunk (Flat) Head Tapping Screws
35	[標準] YJT 4058	十字槽沉頭自攻螺釘 [PT] Cross Recessed Countersunk Head Tapping Screws [PT] 供應商(1)
36	[德標] DIN EN ISO 7050 - 2011	十字槽沉頭自攻螺釘 Cross Recessed Countersunk (Flat) Head Tapping Screws 供應商(3)
37	[美標] ASME B 18.6.3 (H1B-I/H1B-IA+T1A) - 2024	十字槽82度沉頭AB ABR自攻螺釘 82° Cross Recessed Countersunk Head Tapping Screws - Type AB (ABR)
38	[美標] ASME B 18.6.3 (H3B-I/H3B-IA+T1A) - 2024	十字槽82°沉頭清根 AB ABR自攻螺釘 Undercut 82-deg Flat Countersunk Head Tapping Screws - Type AB (ABR)
39	[美標] ASME B 18.6.3 (H4B-I/H4B-IA+T1A) - 2024	十字槽小沉頭 AB ABR自攻螺釘 Flat Coutersunk Trim Head Tapping Screws - Type AB and ABR
40	[美標] ASME B 18.6.3 (T10-I/T10-IA+T40) - 2013	十字槽82°沉頭清根 AB ABR自攻螺釘 Undercut 82-deg Flat Countersunk Head Tapping Screws - Type AB (ABR)
41	[美標] ASME B 18.6.3 (T14-I/T14-IA+T40) - 2013	十字槽小沉頭 AB ABR自攻螺釘 Flat Coutersunk Trim Head Tapping Screws - Type AB and ABR
42	[美標] ASME B 18.6.5M (T10) - 2000 (R2010)	米制米字槽沉頭自攻螺釘 [Table 10] Metric Type IA Cross-Recessed Flat Countersunk Head Tapping Screws [Table 10]
43	[美標] ASME B 18.6.5M (T9) - 2000 (R2010)	米制十字槽沉頭自攻螺釘 [Table 9] Metric Cross Recessed Countersunk Head Tapping Screws [Table 9]
44	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻螺釘 A型 [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 10]
45	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻螺釘 B, BP型 [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 10]
46	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻鎖緊螺釘 C型 (統一螺紋) [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 10]
47	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻螺釘 AB型 [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 10]
48	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻螺釘 A型 [Table 11] Type IA Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 11]
49	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻螺釘 B,BP型 [Table 11] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 11]
50	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻鎖緊螺釘 C型(統一螺紋) [Table 11] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 11]
51	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻螺釘 AB型 [Table 11] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 11]
52	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 A型 [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 12]
53	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 B，BP型 [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 12]
54	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 C型(統一螺紋) [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 12]
55	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 AB型 [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 12]
56	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭清根自攻螺釘 B,BP型 [Table 14] Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 14]
57	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭清根自攻螺釘 C型(統一螺紋) [Table 14] Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 14]
58	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭清根自攻螺釘 AB型 [Table 14] Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 14]
59	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭清根自攻螺釘 B,BP型 [Table 15] Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 15]
60	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭清根自攻螺釘 C型(統一螺紋) [Table 15] Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 15]
61	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭清根自攻螺釘 AB型 [Table 15] Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 15]
62	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭清根自攻螺釘 B,BP型 [Table 16] Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 16]
63	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭清根自攻螺釘 C型(統一螺紋) [Table 16] Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 16]
64	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭清根自攻螺釘 AB型 [Table 16] Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 16]
65	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,B,BP型 [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 17]
66	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,C型(統一螺紋) [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 17]
67	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,AB型 [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 17]
68	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,A型 [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 17]
69	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 B,BP型 [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 18]
70	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 C型(統一螺紋) [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 18]
71	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 AB型 [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 18]
72	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 A型 [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 18]
73	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 B,BP型 [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 19]
74	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 C型(統一螺紋) [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 19]
75	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 AB型 [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 19]
76	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 A型 [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 19]
77	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽100°沉頭自攻螺釘 B,BP型 [Table VI2] Type I Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI2]
78	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽100°沉頭自攻螺釘 AB型 [Table VI2] Type I Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI2]
79	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽100°沉頭自攻螺釘 B,BP型 [Table VI3] Type IA Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI3]
80	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽100°沉頭自攻螺釘 AB型 [Table VI3] Type IA Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI3]
81	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽100°沉頭自攻螺釘 B,BP型 [Table VI4] Type II Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI4]
82	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽100°沉頭自攻螺釘 AB型 [Table VI4] Type II Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI4]
83	[深圳緊固件行業協會標準] T/SZJGJ 001 (C) - 2024	十字槽沉頭自攻螺釘 Cross Recessed Countersunk Head Tapping Screws

十字槽82度沉頭AB ABR自攻螺釘 ASME B 18.6.3 (T2-I/T2-IA+T40) - 2013

同版本產品組

采用標準

工藝相關

AB型和ABR型自攻螺紋和末端

B型 BP型自攻螺釘螺紋和末端

BF型 BT型 自切自攻螺釘螺紋和末端

D, F, G, T 型自攻螺釘 螺紋和末端

A型自攻螺釘螺紋和末端

自擠自攻【TRS型】螺紋和末端

引用參考

BF型 BT型自切自攻螺釘螺紋和末端

D, F, G, T 型自攻螺釘螺紋和末端