會員中心 | English | 繁體中文

十字槽小沉頭 AB ABR自攻螺釘 ASME B 18.6.3 (T14-I/T14-IA+T40) - 2013

選擇規格尺寸點擊↓

4# (3)

5# (4)

6# (4)

6# (5)

8# (5)

8# (6)

10# (8)

12# (8)

12# (10)

1/4 (10)

1/4 (12)

5/16 (12)

5/16 (1/4)

3/8 (5/16)

ASME B 18.6.3 (T14-I/T14-IA+T40) - 2013 十字槽小沉頭 AB ABR自攻螺釘

尺寸單位: inch

美標ASME B18.6.3 (T14-I/T14-IA+T40) - 2013 十字槽小沉頭 AB ABR自攻螺釘

掃一掃分享

公差

螺紋尺寸
d

4#
(3)

5#
(4)

6#
(4)

6#
(5)

8#
(5)

8#
(6)

10#
(8)

12#
(8)

12#
(10)

1/4
(10)

1/4
(12)

5/16
(12)

5/16
(1/4)

3/8
(5/16)

代號	頭部尺寸
d	公稱
PP
d_k	最大值
	最小值
k	參考值
α	最大值
	最小值
槽號
M₁	參考
M₂	參考
P	I型	最大值
		最小值
	IA型	最大值
		最小值
L₀ ^④	公稱
Y ^④	螺紋過渡長度(全螺紋)	最大值
b ^④	螺紋長度 (長螺釘)	最小值

3	4	4	5	5	6	8	8	10	10	12	12	1/4	5/16
0.1120	0.1250	0.1380	0.1380	0.1640	0.1640	0.1900	0.2160	0.2160	0.2500	0.2500	0.3125	0.3125	0.3750
24	20	20	20	18	18	16	14	14	14	14	12	12	12
0.187	0.212	0.212	0.237	0.237	0.262	0.312	0.312	0.362	0.362	0.412	0.412	0.477	0.597
0.167	0.191	0.191	0.215	0.215	0.238	0.285	0.285	0.333	0.333	0.380	0.380	0.442	0.556
0.052	0.060	0.052	0.068	0.052	0.069	0.085	0.069	0.101	0.080	0.112	0.075	0.116	0.155
82°	82°	82°	82°	82°	82°	82°	82°	82°	82°	82°	82°	82°	82°
80°	80°	80°	80°	80°	80°	80°	80°	80°	80°	80°	80°	80°	80°
1	1	1	2	2	2	2	2	2	2	3	3	3	4
0.100	0.122	0.122	0.148	0.158	0.176	0.182	0.192	0.198	0.198	0.262	0.262	0.276	0.358
0.100	0.122	0.122	0.148	0.158	0.176	0.182	0.192	0.198	0.198	0.262	0.262	0.276	0.358
0.061	0.082	0.082	0.075	0.085	0.103	0.110	0.120	0.125	0.125	0.139	0.139	0.154	0.196
0.045	0.066	0.066	0.052	0.062	0.080	0.087	0.097	0.102	0.102	0.116	0.116	0.131	0.174
0.058	0.079	0.079	0.071	0.081	0.099	0.107	0.117	0.122	0.122	0.136	0.136	0.151	0.193
0.042	0.063	0.063	0.053	0.063	0.081	0.089	0.099	0.104	0.104	0.118	0.118	0.133	0.175
13/16	15/16	1	1	1-1/4	1-1/4	1-3/8	1-5/8	1-5/8	1-13/16	1-13/16	1-13/16	1-13/16	1-7/8
0.042	0.050	0.050	0.050	0.056	0.056	0.062	0.071	0.071	0.071	0.071	0.083	0.083	0.083
0.670	0.750	0.830	0.830	0.980	0.980	1.140	1.300	1.300	1.500	1.500	1.500	1.500	1.500

①,若以小數規定公稱直徑，應省略小數前和小數點后第四位的零。
②,螺釘末端釘尖上不允許因螺紋輾壓而形成的虛尖，允許略帶圓弧或圓鈍形末端。
③,小于等于8#的螺釘，螺紋牙頂平面寬度不應超過0.004in，大于8#的應不超過0.006in。
④,正常情況下，當螺釘長度小于等于其公稱長度L0時應采用全螺紋，過渡螺紋長度應小于等于Y；若螺釘長度大于其公稱長度L0可采用半牙型式，但其螺紋長度應不小于b。

替代列表

ASME B 18.6.3T14-I/T14-IA+T40 - 2013 ASME B 18.6.3H4B-I/H4B-IA+T1A - 2024

同版本產品組

ASME B 18.6.3 (T2-I/T2-IA) - 2013

82°十字槽沉頭螺釘 [Table 2] (ASTM F837, F468)

供應商(2)

ASME B 18.6.3 (T1+T40) - 2013

82°開槽沉頭自攻螺釘 AB(ABR)型 [Table 1+Table 40]

ASME B 18.6.3 (T7+T40) - 2013

82°開槽半沉頭 AB ABR 自攻螺釘 [Table 7]

ASME B 18.6.3 (T9+T40) - 2013

開槽82°沉頭清根自攻螺釘 [Table 9+Table40]

ASME B 18.6.3 (T11t) - 2013

80° 開槽半沉頭清根自攻螺釘 [Table 11]

ASME B 18.6.3 (T2-I/T2-IA+T40) - 2013

十字槽82度沉頭AB ABR自攻螺釘

ASME B 18.6.3 (T2-III+T40) - 2013

方槽82度沉頭AB ABR自攻螺釘

ASME B 18.6.3 (T2-VI+T40) - 2013

梅花槽82°沉頭 AB ABR自攻螺釘

ASME B 18.6.3 (T2-VI) - 2013

梅花槽82° 沉頭螺釘

ASME B 18.6.3 (T10-I/T10-IA+T40) - 2013

十字槽82°沉頭清根 AB ABR自攻螺釘

ASME B 18.6.3 (T10-III+T40) - 2013

方槽82°沉頭清根 AB ABR自攻螺釘

ASME B 18.6.3 (T8-I/T8-IA+T40) - 2013

十字槽半沉頭 AB ABR自攻螺釘

ASME B 18.6.3 (T8-III+T40) - 2013

四方槽半沉頭 AB ABR自攻螺釘

ASME B 18.6.3 (T8-VI+T40) - 2013

梅花槽半沉頭 AB ABR自攻螺釘

ASME B 18.6.3 (T12-I/T12-IA+T40) - 2013

十字槽82°半沉頭清根AB ABR自攻螺釘

ASME B 18.6.3 (T12-III+T40) - 2013

四方槽82°半沉頭清根 AB ABR自攻螺釘

ASME B 18.6.3 (T14-I/T14-IA+T40) - 2013

十字槽小沉頭 AB ABR自攻螺釘

ASME B 18.6.3 (T16-I/T16-IA+T40) - 2013

十字槽82°小半沉頭 AB ABR自攻螺釘

采用標準

ASME/ANSI B 18.6.3 (T48) - 2013

自攻螺釘擰入性試驗用標準試驗板厚度和孔徑 [Table 48]

ASME/ANSI B 18.6.3 (T49) - 2013

TRS型自擠自攻螺釘的最大扭矩 [Table 49]

ASME/ANSI B 18.6.3 (T50) - 2013

自攻螺釘的抗扭強度 [Table 50]

ASME B 18.6.3 (DATA-G) - 2013

機械螺釘和自攻螺釘的通用要求

ASME B 18.6.3 (catalog) - 2013

產品表單總覽

工藝相關

ASME B 18.6.3 (T13) - 2013

82°小沉頭十字槽螺釘 [Table 13] (ASTM F837 / F468)

引用參考

鍍鋅、鍍鎳、鍍鎘、復合鍍等層鍍層鹽霧腐蝕的防護性能

GB /T 193 - 2003

普通螺紋（一般用途米制螺紋）- 直徑與螺距系列 (ISO 261: 1998, MOD)

GB /T 5280 - 2002

自攻螺釘用螺紋

注：技術數據僅供參考，請以官方原件為準！

類似標準及供貨信息

1	[國標] GB /T 846 - 2017	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws 供應商(5)
2	[國標] GB /T 846 - 1985	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws 供應商(5)
3	[國標] GB 846 - 1976	十字槽沉頭自攻螺釘 Cross Recessed Countersunk Head Self-tapping Screws 供應商(5)
4	[德標] DIN 7982 - 1990	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws 供應商(3)
5	[國際] ISO 7050 - 2011	十字槽沉頭自攻螺釘 Cross Recessed Countersunk (Flat) Head Tapping Screws 供應商(1)
6	[國際] ISO 7050 - 1983	十字槽沉頭自攻螺釘 Cross Recessed Countersunk Head Tapping Screws 供應商(1)
7	[日標] JIS B 1122 (T6) - 2015	十字槽沉頭自攻釘 Cross Recessed Countersunk Head Tapping Screws
8	[日標] JIS B 1122 (JA4) - 2015	十字槽沉頭自攻釘 - 螺紋型式：Class 1~Class 4 Cross Recessed Countersunk Head Tapping Screws - Threaded Portion are of Class 1 to 4
9	[日標] JIS B 1125 - 2015	十字槽喇叭頭自攻釘 Cross Recessed Trumpet Head Self Drilling Tapping Screw
10	[日標] JIS B 1125 - 2015	十字槽沉頭帶筋自攻釘 Flex. Purpose Drilling Tapping Screws
11	[日標] JIS B 1125 - 2003	十字槽喇叭頭自攻釘 cross Recessed Trumpet Head Self Drilling Tapping Screw
12	[日標] JIS B 1125 - 2003	十字槽沉頭帶筋自攻釘 Cross Recessed Ribbed Countersunk Head Tapping Screws
13	[日標] JIS B 1122 (AAT2) - 1996	十字槽沉頭自攻釘 - 螺紋型式：Class 1~Class 4 [附表2] Cross Recessed Countersunk Head Tapping Screws - Threaded Portion are of Class 1 to 4 [Annex Attached Table 2]
14	[日標] JIS B 1122 (AT2) - 1996	十字槽沉頭自攻釘 [表2] Cross Recessed Countersunk Head Tapping Screws [Table 2]
15	[日標] JIS B 1125 - 1995	十字槽喇叭頭自攻釘 Cross Recessed Bugle Head Self-drilling Tapping Screws
16	[汽標代號] Q 274	十字槽沉頭自攻螺釘 C型 Cross Recessed Countersunk Head Tapping Screws - Type C
17	[汽標代號] Q 278	十字槽沉頭自攻螺釘 F型 Cross Recessed Countersunk Head Tapping Screws - Type F
18	[美標] ASME/ANSI B 18.6.3 - 2010	80°十字槽沉頭自攻釘 80° Machine Screw and Tapping Screw Nuts (Inch Seires)
19	[意大利] UNI 9709 - 1990	塑料用雙螺紋十字槽沉頭(平頭)自攻螺釘 Two-thread Countersunk (Flat) Head Tapping Screws with Cross Rocessed for Plastics
20	[意大利] UNI 6955	十字槽沉頭自攻釘 Cross-Recessed Flat Countersunk Head Tapping Screws
21	[法國] NF E 25-656 - 1994	十字槽沉頭自攻螺釘 Cross Recessed Countersunk (Flat) Head Tapping Screws
22	[英標] BS 4174 - 1972	米字槽80°沉頭自攻釘 [Table 9] Recess 80°countersunk Head Screws - Type Z [Table 9]
23	[英標] BS 4174 - 1972	米字槽80°沉頭清根自攻釘 [Table 11] Recess 80°Truncated Countersunk Head Screws - Type Z [Table 11]
24	[澳標] AS /NZS 4407 - 1996	米制十字槽沉頭自攻螺釘 ISO Metric Cross Recessed Countersunk Head Tapping Screws
25	[原電子工業部] SJ 2822 - 1987	十字槽沉頭自攻釘
26	[原電子工業部] SJ 2498 - 1984	十字槽沉頭自攻釘
27	[韓標] KS B 1032 - 2016 (R2021)	十字槽沉頭自攻螺釘 Cross-Recessed Countersunk (Flat) Head Tapping Screws
28	[韓標] KS B 1032 - 2001	十字槽沉頭自攻螺釘 Cross-Recessed Countersunk (Flat) Head Tapping Screws
29	[標準] YJT 4058	十字槽沉頭自攻螺釘 [PT] Cross Recessed Countersunk Head Tapping Screws [PT] 供應商(1)
30	[德標] DIN EN ISO 7050 - 2011	十字槽沉頭自攻螺釘 Cross Recessed Countersunk (Flat) Head Tapping Screws 供應商(3)
31	[美標] ASME B 18.6.3 (H1B-I/H1B-IA+T1A) - 2024	十字槽82度沉頭AB ABR自攻螺釘 82° Cross Recessed Countersunk Head Tapping Screws - Type AB (ABR)
32	[美標] ASME B 18.6.3 (H3B-I/H3B-IA+T1A) - 2024	十字槽82°沉頭清根 AB ABR自攻螺釘 Undercut 82-deg Flat Countersunk Head Tapping Screws - Type AB (ABR)
33	[美標] ASME B 18.6.3 (H4B-I/H4B-IA+T1A) - 2024	十字槽小沉頭 AB ABR自攻螺釘 Flat Coutersunk Trim Head Tapping Screws - Type AB and ABR
34	[美標] ASME B 18.6.3 (T2-I/T2-IA+T40) - 2013	十字槽82度沉頭AB ABR自攻螺釘 82° Cross Recessed Countersunk Head Tapping Screws - Type AB (ABR)
35	[美標] ASME B 18.6.3 (T10-I/T10-IA+T40) - 2013	十字槽82°沉頭清根 AB ABR自攻螺釘 Undercut 82-deg Flat Countersunk Head Tapping Screws - Type AB (ABR)
36	[美標] ASME B 18.6.5M (T10) - 2000 (R2010)	米制米字槽沉頭自攻螺釘 [Table 10] Metric Type IA Cross-Recessed Flat Countersunk Head Tapping Screws [Table 10]
37	[美標] ASME B 18.6.5M (T9) - 2000 (R2010)	米制十字槽沉頭自攻螺釘 [Table 9] Metric Cross Recessed Countersunk Head Tapping Screws [Table 9]
38	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻螺釘 A型 [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 10]
39	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻螺釘 B, BP型 [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 10]
40	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻鎖緊螺釘 C型 (統一螺紋) [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 10]
41	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭自攻螺釘 AB型 [Table 10] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 10]
42	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻螺釘 A型 [Table 11] Type IA Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 11]
43	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻螺釘 B,BP型 [Table 11] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 11]
44	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻鎖緊螺釘 C型(統一螺紋) [Table 11] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 11]
45	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭自攻螺釘 AB型 [Table 11] Type I Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 11]
46	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 A型 [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type A Thread Forming [Table 12]
47	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 B，BP型 [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 12]
48	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 C型(統一螺紋) [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 12]
49	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭自攻螺釘 AB型 [Table 12] Type II Cross Recessed Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 12]
50	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭清根自攻螺釘 B,BP型 [Table 14] Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 14]
51	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭清根自攻螺釘 C型(統一螺紋) [Table 14] Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 14]
52	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭清根自攻螺釘 AB型 [Table 14] Type I Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 14]
53	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭清根自攻螺釘 B,BP型 [Table 15] Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 15]
54	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭清根自攻螺釘 C型(統一螺紋) [Table 15] Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 15]
55	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽沉頭清根自攻螺釘 AB型 [Table 15] Type IA Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 15]
56	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭清根自攻螺釘 B,BP型 [Table 16] Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 16]
57	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭清根自攻螺釘 C型(統一螺紋) [Table 16] Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 16]
58	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭清根自攻螺釘 AB型 [Table 16] Type II Cross Recessed Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 16]
59	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,B,BP型 [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 17]
60	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,C型(統一螺紋) [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 17]
61	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,AB型 [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 17]
62	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽沉頭精整自攻螺釘,A型 [Table 17] Type I Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 17]
63	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 B,BP型 [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 18]
64	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 C型(統一螺紋) [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 18]
65	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 AB型 [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 18]
66	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型十字槽沉頭精整自攻螺釘 A型 [Table 18] Type IA Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 18]
67	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 B,BP型 [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type B and BP Thread Forming [Table 19]
68	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 C型(統一螺紋) [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type C Thread Forming [Table 19]
69	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 AB型 [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type AB Thread Forming [Table 19]
70	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽沉頭精整自攻螺釘 A型 [Table 19] Type II Cross Recessed Flat Countersunk Trim Head Tapping Screws - Type A Thread Forming [Table 19]
71	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽100°沉頭自攻螺釘 B,BP型 [Table VI2] Type I Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI2]
72	[美標] ASME B 18.6.4 - 1998 (R2005)	I型十字槽100°沉頭自攻螺釘 AB型 [Table VI2] Type I Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI2]
73	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽100°沉頭自攻螺釘 B,BP型 [Table VI3] Type IA Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI3]
74	[美標] ASME B 18.6.4 - 1998 (R2005)	IA型米字槽100°沉頭自攻螺釘 AB型 [Table VI3] Type IA Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI3]
75	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽100°沉頭自攻螺釘 B,BP型 [Table VI4] Type II Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI4]
76	[美標] ASME B 18.6.4 - 1998 (R2005)	II型十字槽100°沉頭自攻螺釘 AB型 [Table VI4] Type II Cross Recessed 100°Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI4]
77	[深圳緊固件行業協會標準] T/SZJGJ 001 (C) - 2024	十字槽沉頭自攻螺釘 Cross Recessed Countersunk Head Tapping Screws