會員中心 | English | 繁體中文

中部帶1/2全長平行溝槽的槽銷 EN ISO 8743 - 1997

選擇規格尺寸點擊↓

Φ1.5

Φ2

Φ2.5

Φ3

Φ4

Φ5

Φ6

Φ8

Φ10

Φ12

Φ16

Φ20

Φ25

尺寸單位: mm

歐標EN ISO 8743 - 1997 EN ISO8743 8743EN I 中部帶1/2全長平行溝槽的槽銷

掃一掃分享

單重計算公差

公稱直徑
d

Φ1.5

Φ2

Φ2.5

Φ3

Φ4

Φ5

Φ6

Φ8

Φ10

Φ12

Φ16

Φ20

Φ25

d	最大值
	最小值
c
最小剪切載荷,雙面剪,kN
d₁	公差

1.5	2	2.5	3	4	5	6	8	10	12	16	20	25
1.475	1.975	2.475	2.975	3.925	4.925	5.925	7.91	9.91	11.89	15.89	19.87	24.87
0.2	0.25	0.3	0.4	0.5	0.63	0.8	1	1.2	1.6	2	2.5	3
1.6	2.84	4.4	6.4	11.3	17.6	25.4	45.2	70.4	101.8	181	283	444
+0.05	+0.05	±0.05	±0.05	±0.05	±0.05	±0.05	±0.05	±0.05	±0.1	±0.1	±0.1	±0.1

d₁ / 公稱

①,槽角a 應根據材料的變形量由工藝確定；對易切鋼制成的槽銷，a≈70°。

替代列表

EN 28743 - 1992 EN ISO 8743 - 1997

等效標準

國標 GB	國際 ISO	德標 DIN	歐標 EN
GB /T 13829.4	ISO 8743	DIN EN ISO 8743	EN ISO 8743

以上有部分標準可能為近似等效，如有異議以標準原件為準

采用標準

ISO 8743 - 1997

中部帶1/2全長平行溝槽的槽銷

技術條件和引用標準

材料 ^①

鋼

奧氏體不銹鋼

硬度
溝槽
表面處理
表面缺陷
抗剪強度試驗
驗收及包裝
備注

硬度 125~245 HV30	A1（ISO 3506-1）硬度 210~280 HV30
槽的形狀由生產者任選
Plain, i.e. pins to be supplied in natural finish treated with a protective lubricant, unless otherwise specified by agreement between customer and suppller. Preferred coatings are black oxide, phosphate coating or zinc plating with chromate conversion coating (see ISO 9717 and ISO 4042). 其他表面鍍層或表面處理應由供需雙方協議。所有公差僅適用于涂、鍍前的公差。	Plain, i.e. pins to be supplied in natural finish.
不允許有不規則的和有害的缺陷。
ISO 8749	-
ISO 3269
① 其他材料由供需雙方協議

引用參考

GB /T 1172 - 1999

黑色金屬硬度及強度換算值

GB /T 5267.1 - 2002

鍍鋅、鍍鎳、鍍鎘、復合鍍等層鍍層鹽霧腐蝕的防護性能

GB /T 193 - 2003

普通螺紋（一般用途米制螺紋）- 直徑與螺距系列 (ISO 261: 1998, MOD)

注：技術數據僅供參考，請以官方原件為準！

類似標準及供貨信息

1	[國標] GB /T 13829.1 - 2004	槽銷帶導桿及全長平行溝槽 Grooved Pin, Full Length Parallel Grooved with Pilot 供應商(2)
2	[國標] GB /T 13829.2 - 2004	槽銷帶倒角及全長平行溝槽 Grooved Pin, Full Length Parallel Grooved with Chamfer 供應商(3)
3	[國標] GB /T 13829.3 - 2004	槽銷中部槽長為1/3全長 Grooved Pins-One-Third-Length Centre Grooved 供應商(3)
4	[國標] GB /T 13829.4 - 2004	槽銷中部槽長為1/2全長 Grooved Pins - Half-Length Centre Grooved 供應商(1)
5	[國標] GB /T 13829.1 (A) - 1992	A型-帶導桿及全長平行溝槽的槽銷. Grooved Pin, Full Length Parallel Grooved with Pilot 供應商(2)
6	[國標] GB /T 13829.1 (B) - 1992	B型-帶倒角及全長平行溝槽槽銷. Grooved Pins-full-length Parallel Grooved, with Chamferw 供應商(3)
7	[國標] GB /T 13829.1 (C) - 1992	C型-中部帶1/3全長平行溝槽的槽銷 Grooved Pins-one-third-length Centre Grooved 供應商(3)
8	[國標] GB /T 13829.1 (D) - 1992	D型中部帶1/2全長平行溝槽的槽銷 Grooved Pins - Half-length Centre Grooved 供應商(1)
9	[德標] DIN 1469 - 2012	帶頸配合槽銷，溝槽長為全長1/2 Grooved Pins, Half Length Grooved with Gorge 供應商(1)
10	[德標] DIN 1469 - 2011	帶頸配合槽銷 Grooved Pins, Half Length Grooved with Gorge 供應商(1)
11	[德標] DIN 1469 - 1978	帶頸配合槽銷 Grooved Pins, Half Length Grooved with Gorge 供應商(1)
12	[德標] DIN 1470 - 1978	帶導桿及全長平行溝槽的槽銷 Grooved pin, full length parallel grooved with pilot 供應商(1)
13	[德標] DIN 1473 - 1978	帶倒角及全長平行溝槽的槽銷 Grooved Pins, Full Length Parallel Grooved with Chamfer 供應商(2)
14	[德標] DIN 1475 - 1978	槽銷，中部槽長為1/3全長 Grooved Pins - 1/3 Length Centre Grooved 供應商(2)
15	[國際] ISO 8739 (RN) - 2025	帶導桿及全長平行溝槽, 倒圓端 Pin with Pilotpoint and Rounded Ends 供應商(1)
16	[國際] ISO 8740 (RN) - 2025	帶倒角及全長平行溝槽槽銷-倒圓端 ? Pin with chamfered point and rounded ends (RN) 供應商(2)
17	[國際] ISO 8739 - 1997	槽銷—帶導桿及全長平行溝槽 Grooved Pins-Full-Length Parallel Grooved, with Pilot 供應商(1)
18	[國際] ISO 8740 - 1997	帶倒角及全長平行溝槽槽銷 Grooved Pins-Full-Length Parallel Grooved, with Chamfer 供應商(2)
19	[國際] ISO 8742 - 1997	中部帶1/3全長平行溝槽的槽銷 Grooved Pins-One-Third-Length Centre Grooved 供應商(1)
20	[國際] ISO 13672 (RN) - 2025	槽銷半長平行溝槽末端倒圓 Parallel Grooved Pins - Half-length Diamond Grooves - Rounded Ends
21	[國際] ISO 13672 (CH) - 2025	槽銷半長平行溝槽末端倒角 Parallel Grooved Pins - Half-length Diamond Grooves - Chamfered Ends
22	[國際] ISO 8739 (CH) - 2025	帶導桿及全長平行溝槽, 倒角端 Pin Pilot Point and with Chamfered Ends
23	[國際] ISO 8740 (CH) - 2025	帶倒角及全長平行溝槽槽銷-倒角端 Pin with Both Chamfered Points (CH)
24	[國際] ISO 8743 - 1997	中部帶1/2全長平行溝槽的槽銷 Grooved Pins-Half-Length Centre Grooved
25	[美標] ASME/ANSI B 18.8.100M (B18.8.9M T5) - 2000 (R2005)	米制半長溝槽槽銷 TYPE 43-1 / TYPE 43-2 [TABLE 5] Metric, Grooved Pins with Half-length Groove, TYPE 43-1 / TYPE 43-2 [TABLE 5]
26	[美標] ASME/ANSI B 18.8.100M (B18.8.9M T3) - 2000 (R2005)	米制全長平行溝槽槽銷 TYPE 39 / TYPE 40 [Table 3] Grooved Pins, Full-length Parallel Grooved - Metric Series, TYPE 39 / TYPE 40 [Table 3]
27	[美標] ASME/ANSI B 18.8.100M (B18.8.9M T4) - 2000 (R2005)	米制中部槽長1/3全長平行溝槽槽銷 TYPE 42 [TABLE 4] Metric, Grooved Pins with One Third Length Groove in the Middle, TYPE 42 [TABLE 4]
28	[美標] ASME/ANSI B 18.8.100M (B18.8.9M T4) - 2000 (R2005)	米制中部帶1/2全長平行溝槽槽銷 TYPE 43 [TABLE 4] Metric Grooved Pins, Half-length Centre Grooved, TYPE 43 [TABLE 4]
29	[歐標] EN 28740 - 1992	槽銷全長平行溝槽帶倒角 Full-Length Parallel Grooved, with Chamfer
30	[歐標] EN 28743 - 1992	中部帶1/2全長平行溝槽的槽銷 Grooved Pins - Half-Length Centre Grooved
31	[法國] NF E 25-750 - 1997	中部帶1/2全長平行溝槽的槽銷 Grooved Pins. Half Length Centre Grooved
32	[法國] NF E 25-761 - 1997	槽銷帶導向的全長平行槽 Grooved Pins - Full-length Parallel Grooved, With Pilot
33	[法國] NF E 25-763 - 1997 (R2002)	中部帶1/3全長平行溝槽的槽銷 Grooved Pins. One-Third-Length Centre Grooved
34	[法國] NF E 25-772 - 1997 (R2002)	帶倒角及全長平行溝槽的槽銷 Grooved Pins. Full Length Paralled Grooved, with Chamfer
35	[美標] SAE J 494 (C) - 2004	C型槽銷 Grooved Straight Pins - Type C
36	[美標] SAE J 494 (E) - 2004	E型槽銷 Grooved Straight Pins - Type E
37	[美標] SAE J 494 (F) - 2004	F型槽銷 Grooved Straight Pins - Type F
38	[德標] DIN EN ISO 8739 - 1998	帶導桿及全長平行溝槽的槽銷 Grooved Pin, Full Length Parallel Grooved with Pilot 供應商(1)
39	[德標] DIN EN ISO 8740 - 1998	帶倒角及全長平行溝槽的槽銷 Grooved Pins. Full-Length Parallel Grooved, with Chamfer 供應商(2)
40	[德標] DIN EN ISO 8742 - 1998	槽銷，中部帶1/3全長平行溝槽 Grooved Pins - 1/3 Length Centre Grooved 供應商(2)
41	[德標] DIN EN ISO 8743 - 1998	槽銷中部槽長為1/2全長 Grooved Pins - Half-Length Centre Grooved
42	[美標] ASME B 18.8.2 - 2020	F型全長槽銷 [Table 8-1] Grooved Pins - Type F
43	[美標] ASME B 18.8.2 - 2020	H型半長槽銷 [Table 8 -1] Grooved Pins - Type H
44	[美標] ASME B 18.8.2 - 2020	G型槽銷 [Table 8 -1] Grooved Pins - Type G
45	[美標] ASME B 18.8.2 - 2020	E型槽銷半長錐槽 [Table 8 -1] Grooved Pins - Type E
46	[美標] ASME B 18.8.2 - 2000 (R2010)	H型半長槽銷 [Table 6] Grooved Pins - Type H
47	[美標] ASME B 18.8.2 - 2000 (R2010)	E型槽銷半長錐槽 [Table 6] Grooved Pins - Type E
48	[美標] ASME B 18.8.2 - 2000 (R2010)	F型全長槽銷 [Table6] Grooved Pins - Type F
49	[美標] ASME B 18.8.2 - 2000 (R2010)	G型槽銷 [Table 6] Grooved Pins - Type G
50	[航空] HB 858 - 1990	D型導正銷